crank sprocket puller tool? - Dodge SRT Forum
Jun 11, 2008 · 1378 posts · Joined 2006. #31 · Oct 18, 2013. The insert goes in the crank so the tool can pull the sprocket off. If you don't have the insert or something similar, the large bolt in the sprocket tool wont have anything to push against to get the sprocket off. Butter shifting trans using ATF fluid :goats:
what tools(s) to remove cam sprockets? | Dodge SRT Forum
Jan 1, 2009 · 1) crank pulley puller. 2) crank pulley installer. 3) cam sprocket holder. Not averse to buying them (the right tool makes the job WAY easier) but none of the threads I've reviewed have been specific about which tools (except in a general way) can be used and what tools are available outside of the Miller tools.
Crankshaft sprocket removal. My life can't get ANY worse.
Jan 10, 2007 · A new sprockets only like $20 from Chrysler. Its hard to do without destrying the oil pump or nicking the keyway or crank, buts its a last resort type of thing. the coil bolts are the correct to thread into the sprocket. I used a toool for older 2.2/2.5 motors (had to drill 1 hole in it to get the 3rd bolt to line up).
HOW-TO: Remove & Install Oil Pump | Page 4 | Dodge SRT Forum
Jul 3, 2009 · SRT-4 FAQ / How To. How To Forum. HOW-TO: Remove & Install Oil Pump
Where to get special tool 6793 - Dodge SRT Forum
Jan 10, 2006 · Crank Sprocket Remover - Chrysler, Jeep, Dodge. What we did was find a flat piece of steel, drill three holes in it (that line up with the holes on the sprocket of course), found three bolts that fit the thread pattern on the sprocket, and then just slowly tighten each one till it pops the sprocket off. Cost=nada.
crank sprocket puller tool? | Page 2 | Dodge SRT Forum
Feb 26, 2009 · 1378 posts · Joined 2006. #31 · Oct 18, 2013. The insert goes in the crank so the tool can pull the sprocket off. If you don't have the insert or something similar, the large bolt in the sprocket tool wont have anything to push against to get the sprocket off. Butter shifting trans using ATF fluid :goats:
crankshaft sprocket - Dodge SRT Forum
May 9, 2007 · The 2.4 Liter (148 cu. in.) in-line four cylinder engine is a double over head camshaft with hydraulic lifters and four valve per cylinder design. The engine is free-wheeling; meaning it has provisions for piston-to-valve clearance. However valve-to-valve interference can occur, if camshafts are rotated independently.
Looking to rent/borrow crank sprocker puller. | Dodge SRT Forum
Jan 23, 2015 · 1695 posts · Joined 2003. #2 · Jan 24, 2015. you can rent a chrysler tool from autozone that will remove the crank pulley, the crank sproket you can you rent a regular crank puller to remove it. to put it back on you can use your stock crank bolt and a socket that will fit over the nose of the crank, have a set of feeler gauges to make sure ...
Installing cams, how do I find TDC? | Dodge SRT Forum
Mar 10, 2007 · 2) get a pulley puller and pull the crank pulley, then pull the lower shield off...you will see 2 arrows, one on the oil pump, and one on the teeth of the gear on the crank. (line these up so that the 2.4L on the cam gears are reading upright) Remember car motors are 2 stroke motors so if the 2.4L marking is upside down, turn the motor over one ...
Help with Crank Sprocket - Dodge SRT Forum
Feb 17, 2012 · Straight from Darrell Cox: "With the OE install tool it sets the crank gear .035-.038 thou. gap from the oil pump housing. The distance from the end of the crank to the inward side of the crank gear is 1.042 thou. Never use a hammer or any impacting to install the crank gear or pulley. Damage to the engine thrust bearing and crankshaft can occur."